| Error Code | Error Code Name | Description | Potential Cause | Solution |
| E01 | Initialization | The table has an unknown position and needs to be initialized | Position error or a new lifting column has been added | Initialize the Control Box (see Common Procedures) |
| E08 | Watchdog | Software failed to activate routine that checks calculations | Program fault | Unplug Power Cable for 15 seconds. Initialize the Control Box (see Common Procedures) Replace Control Box. |
| E10 | Power fail | Power fail happened | Power Cord pulled during driving or there is an internal fault | Check Power Cord is not caught, and is allowed to freely travel. Plug table into reliable 120v/240v outlet and test. Replace Power Cable or Control Box. |
| E11 | Port/Channel mismatch | Change in number of Lifting Columns since initialization | Disconnection or a lifting column has been added | Check Low-Voltage Cable connections and integrity. Change Low-Voltage Cable or Lifting Column. Initialize the Control Box (see Common Procedures) |
| E12 | Position error | One Port/Channel has a different position than others | Too much back drive occurred | Move table to the lowest position and initialize control box |
| E13 | Short circuit | One of the motor outputs has short-circuited | Squeezed low voltage cable or a short within the motor | Check Low-Voltage Cable connections. Isolate and replace Low-Voltage Cable. Isolate and replace Lifting Column |
| E15 | Power limit | System has reached its power limitation | Low-Voltage Cable pulled during driving. Internal fault | Check Low-Voltage Cable is not caught, and is allowed to freely travel. Use strain-relief loop built into control box |
| E16 | Button error | Illegal buttons pressed | Hitting multiple buttons simultaneously | Check controller |
| E17 | Safety missing | LIN bus unit does not support safety feature | Controller does not have up-to-date software | Check Controller |
| Error Code | Error Code Name | Description | Potential Cause | Solution |
| E23, E24, E25 | Port/channel 1,2,3 missing respectively | Port/channel 1,2,3 are detected missing respectively | Disconnection | Check low voltage cable connections and integrity. Change low voltage cable or lifting column. |
| E29, E30, E31 | Port/channel 1,2,3 pulse fail respectively | Port/Channel 1 is not same type as when initialized. Port/Channel 2, 3 are not same type as when initialized or not same type as Port/Channel 1. | Change in lifting column type | Checking lifting column type, change lifting column, and initialize control box. |
| E35, E36, E37 | Port/channel 1,2,3 pulse fail respectively | Port/Channel 1, 2, 3 had too many pulse errors respectively | Loose/faulty low voltage cable. Hall sensor PCB inside lifting column. | Check Low-Voltage Cable connections and integrity. Initialize the Control Box (see Common Procedures). Replace Lifting Column |
| E41,E42, E43 | Overload | Overload up occurred on Port/Channel 1, 2, 3 respectively | Hit obstruction, leg is overloaded, reached end stop | Remove obstruction. Remove load. Initialize the Control Box (see Common Procedures), if necessary |
| E47, E48, E49 | Overload | Overload down occurred on Port/Channel 1, 2, 3 respectively | Reached end stop. Hit obstruction | Remove the obstruction. Initialize the control box |
| E53, E54, E55 | Collision | Anti collision triggered on Port/Channel 1, 2, 3 respectively |
Hit obstruction | Remove obstruction & initialize the control box |
| E59, E60, E61 | Collision | Safety limit switch activated on Port/Channel 1, 2, 3 respectively | Hit obstruction | Remove obstruction & initialize the control box |
| E65, E66, E67 | Port/channel 1,2,3 pulse direction respectively | Pulses counted wrong direction in Port/Channel 1, 2, 3 respectively | Motor poles are crossed. Hall sensor cables crossed inside of the lifting column. | Check low-voltage cab connections and integrity. Initalize the control box & replace the lifting column |
| E71 | Ch1A Short | Short circuit on channel 1 (lfT-splitter is used, short circuit on 1A) | Damage to power cable, damage to cable exiting leg | Inspect power cable for damage, replace if damaged. Inspect cable exiting leg & replace if damaged. |
| E72 | Ch1B Short | Short circuit on channel 1 (lfT-splitter is used, short circuit on 18) | Damage to power cable, damage to cable exiting leg | Inspect power cable for damage, replace if damaged. Inspect cable exiting leg & replace if damaged. |