To download the User Guide, click here.
3 Preset Programmable Controller with Digital Display
OPERATING THE CONTROLLER
- Press and hold either the up or down button to reach the desired height. The digital controller will display the current height of the desk.
- To adjust to a stored height in memory, use the three memory position buttons.
- Press and hold the numbered button that has the saved height stored into memory.
- The desk will raise or lower until it reaches the stored height. The controller will display the current height of the desk as it adjusts.
- The digital display will turn off after 10 seconds of no activity. Press the up, down or preset button to activate the display.
- The user must continuously hold down the button in order for the desk to move.
STORE HEIGHT INTO MEMORY
To set into memory the desired height for either seated or standing work, use the three memory position buttons.
- Press either the up or down button to reach the desired height.
- Press the s button once.
- The display will flash s for 2 seconds. During this time press your choice of memory position buttons 1-3 to set that particular height. The display will store by showing 1, 2 or 3 for 1 second.
To save additional heights repeat this sequence using the remaining two buttons.
ADJUSTING THE HEIGHT DISPLAYED
The controller will show 22.6" at its lowest setting which is the default setting from the factory. If you need to adjust the height displayed:
- At the same time, press the up and down buttons for 5 seconds. The display will show --- (three dashes), then the display will show the height.
- Adjust the displayed height using the up or down buttons. After 5 seconds of inactivity the height will blink once setting the new height.
Note: This controller does not allow switching from inches to centimeters.
Cable Management
When installing equipment, either on the worksurface or below, be sure that the connecting cables are free from obstruction. A trough is provided to manage excess base controller wires and can be found on the underside of the worksurface. Use this trough to minimize possible entanglements.
Workstation Design Tips
- Ensure that power cords for all accessory items – computer, lights, monitors, etc. – are of sufficient length to reach outlets throughout the range of worksurface height adjustment. Do not subject the cords to any strain while adjustment of the surface is taking place.
- Always check for proper operating clearance before placing any item on, above or below the worksurface.
Maintenance and Cleaning
Regularly clean dust and dirt from lifting columns. To ensure all surfaces are thoroughly cleaned, make sure the lifting columns are fully extended to their maximum height. Also, be sure to inspect cables and lifting columns for damage. Check all connections for both correct function and secure mounting.
A damp cloth is recommended. To protect the painted surfaces, use a cleanser that is not highly alkaline or acidic. A pH neutral product is ideal.
Notice: Please do not move the desk without help. Refer to the guidelines at the end of the assembly instructions, or contact your facilities group for assistance.
WARNING
To reduce risk of electric shock, always unplug desk from the electrical power outlet before cleaning.
Troubleshooting
If you are having trouble with your desk, try the simple steps outlined below. If problems persist, please refer to the Elective Elements Height-Adjustable Desk troubleshooting guide.
DESK WILL NOT FULLY ADJUST
- Check that the power cable is fully plugged into the outlet.
- Check that the power cable is fully plugged into the control box under the desk.
- Check that the desk is not overloaded. The weight load should be evenly distributed.
- Synchronize the lifting columns as outlined below.
POWER-SAVING CONTROL BOX:
- The control box automatically powers down into ‘standby’ mode after approximately 10 seconds of inactivity.
- During standby mode, the control box only consumes 0.1 watt of power.
- With the control box in standby mode, the desk can lose power without affecting the synchronization of the lifting columns. However, if the control box is still active, and not in standby mode, a power loss will require that the lifting columns be re-synchronized.
- Power fluctuations and brownouts can also cause the need for resynchronization.
Note: The control box does not re-set (initialize) by being unplugged and plugged back in. Refer to the initialization procedure below.
INITIALIZING THE CONTROL BOX:
- In the unlikely event that an error occurs, press and hold the up and down button simultaneously for 5 seconds to reset the control box.
- Synchronize the lifting columns as outlined below.
SYNCHRONIZING LIFTING COLUMNS:
- Operate the desk all the way down to the lowest position, and release the down button.
- Press the down button again, and hold.
- After a few seconds, the desk will visibly move up and down, settling to its correct ‘bottom’ position.
- The lifting columns are now synchronized via the software in the control box.
- Operate the desk all the way up and down to confirm proper function.